Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung | Nächste ÜberarbeitungBeide Seiten der Revision | ||
en:anleitungen:ikea_schild [2016-06-12 17:38] – Freese | en:anleitungen:ikea_schild [2016-06-12 22:56] – Malin | ||
---|---|---|---|
Zeile 21: | Zeile 21: | ||
{{ : | {{ : | ||
- | Remove the base. That is easily done by using a sharp knive and a screwdriver for levering. | + | Remove the base. This is easily done by using a sharp knive and a screwdriver for levering. |
- | Next you need to get the center hole. In my case a small part of the center seen in the picture just cracked | + | Next you need to make the center hole. In my case a small part of the center seen in the picture just fell out while taking away the base which was quite convienent. Otherwise you drill a hole that can be easily be made bigger afterwards by cutting along the coiled |
{{: | {{: | ||
{{: | {{: | ||
- | \\ You can see the excised stripes | + | \\ You can see the excess strips |
- | Sand the edges on the inside and outside afterwards to get them rounded nicely. | + | Sand the edges on the inside and outside afterwards to get them rounded nicely. |
{{: | {{: | ||
- | Detailed pictures showing the edges of the insinde | + | Detailed pictures showing the edges of the inside |
{{: | {{: | ||
Zeile 38: | Zeile 38: | ||
=== Covering with cloth === | === Covering with cloth === | ||
- | Next you need the cloth and the wood glue. At first the inner side of the shield | + | Now you need the cloth and the wood glue. You should do the the inner side of the shield |
{{: | {{: | ||
- | Cut some of the cloth in the center hole off but leave about 1 cm protruding. Stick it to the bowl by turning it over to the outer side.\\ | + | Cut the cloth away in the center hole, leaving |
{{: | {{: | ||
- | Proceed in the same manner with the cloth on the other edges and let it dry for a couple of hours when you are done. | + | Proceed in the same manner with the cloth on the other edge and let it dry for a couple of hours. |
- | As the glue is all dried, the other side of the bowl is going to be covered with cloth as well. The process is the same as before: First do a rough cutting, | + | When the glue is all dried, |
{{: | {{: | ||
- | After some short surface | + | After a short drying |
Inside:\\ | Inside:\\ | ||
Zeile 63: | Zeile 63: | ||
- | You can use the time to look for a piece of wood that will work as a handle for the shield. A curved branch | + | You can use the time to look for a piece of wood that will work as a handle for the shield. A curved branch |
{{: | {{: | ||
- | At this point you can also paint the shield if you want to. | + | At this point you can also paint the shield, if you want to. |
===Edging=== | ===Edging=== | ||
- | In this next step the rawhide is attached to the buckler to get a robust edging. | + | In this step the rawhide is attached to the buckler to get a robust edging. |
- | First the rawhide has to be laid in water to get it flexible (some soap helps to prevent the inconvenient reek) and - if required - cut in stripes. For good handling the striped | + | First the rawhide has to be soaked |
- | These stripes | + | These strips |
{{: | {{: | ||
- | Be mindful of an adequate overlapping of the stripes | + | Be mindful of an adequate overlapping of the strips, |
\\ | \\ | ||
- | Many people prefer to attach the rawhide as long as it is wet, because this builds up extra tension on the shield which is useful when it is made from planks. But in the case shown in this instruction it is rather a disadvantage, | + | Many people prefer to attach the rawhide as long as it is wet, because this builds up extra tension on the shield which is useful when it is made from planks. But in the case shown in this instruction it is rather a disadvantage, |
\\ | \\ | ||
- | You should change the positions of the clamps two or three times while the rawhide is drying because it's more difficult for the water to evaporate from underneath a clamp.\\ | + | You should change the positions of the clamps two or three times while the rawhide is drying, because it's more difficult for the water to evaporate from underneath a clamp.\\ |
- | Check the position of the rawhide on the edge as soon as it has dried and may correct | + | Check the position of the rawhide on the edge as soon as it has dried and correct |
- | Then you drill holes through the rawhide and the shield and attach the rawhide to the shield. You can use parcel string to have a very robust | + | Then you drill holes through the rawhide and the shield and attach the rawhide to the shield. You can use parcel string to have a very robust |
- | This attachment | + | This method |
===Riveting=== | ===Riveting=== | ||
In a very last step handle, shield boss and shield have to be connected to each other.\\ | In a very last step handle, shield boss and shield have to be connected to each other.\\ | ||
- | A simple and stable option | + | For a simple and stable option |
===Finished=== | ===Finished=== |